Dynoed My Truck

[adrenaholc1]

First of all my trans not build and its not slipping thank god!
and the weather was very humid yesturday and hot.
I also think i have a problem with my waste gate i get only 21 PSI of boost.

By the list of vehicles in your sig it's safe to say " if I had your money, I'd burn :rofl:all mine. " Get your Trans built, add another charger, get REAL tuning and be ready to :thumb:feel some lambo crushing torque.

 

[MKS]

LOL guys, i am selling this truck! I got a 2008 gmc duramax dually:woott:. and if this dually i just got didnt get me good number i will burn it .

My old truck the lb7 didnt get good numbers but i raced a Denali with a tune, cam, headers, intake, cold air intake, exhaust and much more, he was disppointed since his window was open and he inhaled the black smoke lol for 3 seconds and i was gone :roflmao: soo those numbers suck but have a great impact on the road :thumb:

 

[Dan@PPE]

MKS,

Your truck should be making right at 500 RWHP (as long as all the parts on the truck are good condition). The truck should run in the low 12's.

 

[McRat]

The Hot +2 has probably put more trucks in the 12's than all the other handheld's combined. If any.

It's tune is not all that different than a typical EFILive full race tune.

 

[hondarider552]

Well I don't know about small rollers the rollers on our dyno are 36" diameter weigh in at 1850#. But I really don't care about comparing #s between dynos. If the tune is good to go, unstrap it and introduce it to the real world.

1850 lbs isnt even enough for my Colorado.

For diesels, roller mass needs to exceed 7000 lbs +, to be accurate, from what I have seen

 

[blk smoke lb7]

Check your boots and clamps buy new if you must but it sounds to me like you have a boost leak somewhere or the intercooler is leaking badly.If your gauge is fairly accurate I would think you should see peak boost #s around 30.Either that or your loosing drive pressure.IMO

 

[McRat]

If you can, post your dyno graph. I can often tell a lot by looking at it.

 

[Noreaster]

Im surprised the tranny isn't limping

 

[MKS]

thanks guys i sold the truck let the new owner deal with it lol i just got a gmc sierra dually 08, gona have eric send me hot+2 for it.

 

[Boostjunkie]

What dyno has a roller that weighs 7000#s? I looked up several dynos that are the most popular dynos that are rated to 3000hp and shipping weight on those dynos are less than 5000#.

 

[McRat]

What dyno has a roller that weighs 7000#s? I looked up several dynos that are the most popular dynos that are rated to 3000hp and shipping weight on those dynos are less than 5000#.

Superflows, Mustangs, and Dynojets (with retard) can put eddy current load on the roller. I know a Superflow can mimic a 10 second pass for a 6500lb truck (ie - same load as in real life drag pass)

 

[hondarider552]

What dyno has a roller that weighs 7000#s? I looked up several dynos that are the most popular dynos that are rated to 3000hp and shipping weight on those dynos are less than 5000#.

Dynojet 244HW. 90% of all dynos out there cannt load out trucks properly with the same weight applied, compared to the trucks weight. I dyno'd my neighbors stock 6.4 ford, and the 3800 lbs resistance mustang said it put down 355rwhp...

 

[Boostjunkie]

Now I'm following, yes I do agree! Never tried loading the dyno over 4500# have to try next time.

 

[Bonestock]

My LB7 made 549 on one dyno and 548 on another dyno. This truck has stock cp3 stock injectors, stock turbo with boost valve and fass 150 lift pump.

EPR Tuning EFI Live