LBZ: 11.53 @116.92

[mytmousemalibu]

:bananallama: :coal:

 

[KEVINL]

Thats damn quick

I don't think you need twins

 

[Mike L.]

Thats damn quick

I don't think you need twins

Well of course he does Kevin. His poor single is straining pulling his truck weight. ( I am being kind Henry ):hug:

 

[ripmf666]

Well of course he does Kevin. His poor single is straining pulling his truck weight. ( I am being kind Henry ):hug:

Mike I was hoping George showed up, I was going to sucker him into driving to save a few hundred pounds :hug:

 

[emiller3]

Congrats,thats movin.hope to see you go faster with tuning

 

[Big Angry]

Have to thank Ted Big Angry for the Video he did, I could not bring my camara.

Congrats Henry on the run, I'm just glad that I got that one on video, and it didn't turn out too bad.
See you next week at Numidia! :coolspot:

 

[ripmf666]

Congrats Henry on the run, I'm just glad that I got that one on video, and it didn't turn out too bad.
See you next week at Numidia! :coolspot:

Hope to not sure if i might just watch or race or dyno lol

 

[dmaxvaz]

henry, thats awsome! congrats, looks like the new tuning is working:coolspot:

 

[estelly]

THAT WAS A NICE PASS I HOPE THE TUNING WORKS OUT FOR YOU BUT WHAT DO YOU THINK THE TRUCK WOULD RUN IF IT WERE TUNED BY ROB PAT OR MARK :angel:

 

[emiller3]

X2:spit:

 

[racinmike77]

Good job henry looks like the new rubber did the trick. CONGRATS

 

[whitetrash21]

right on henry. 11's finally. congrats

 

[JoshH]

Big congrats Henry. You deserve it. Looks like you have your 60' times down.

Yea i'm in 6th just pass if not right on the 1/8 mile mark.around 4,000-4,200 alittle past the timing towers.

You sure that isn't 5th? I was hitting 5th right at the 1/8, and I was just hitting 6th at the traps when I was trapping in the 110 range. I programmed it out of the ECM to shave a few hundredths off my ET, and I was still under 3500 RPMs in 5th at those speeds. Are you running some really small tires or a gear ratio lower than 3.73s?

 

[sweetdiesel]

Congrats Henry

 

[05_LLY]

Congrats Henry glad its al comin together! Look me up at Numedia!!

 

[draftee]

Congrats Henry.......That truck runs very good and has more in it.... Now, change intake....

 

[Stingpuller]

6th gear

WOW! I only get into 5th at 1000 ft or so. I know I run a taller tire but wow. I would think that would be hard on the tranny. O well whatever it takes to GET ER DONE. Is that turbo still for sale now that you run in the 11's? nice run again jeff

 

[Huntinducks82]

Congrats Henry. I was there to see that pass. Truck runs and sound good.

 

[ripmf666]

WOW! I only get into 5th at 1000 ft or so. I know I run a taller tire but wow. I would think that would be hard on the tranny. O well whatever it takes to GET ER DONE. Is that turbo still for sale now that you run in the 11's? nice run again jeff

Jeff I think the rpms in the tcm tunning need raised alittle more, Truck shifted thru the gears really fast, I think it would pull hard thru the mid track if it stayed in 5th longer.

 

[ripmf666]

Big congrats Henry. You deserve it. Looks like you have your 60' times down.
You sure that isn't 5th? I was hitting 5th right at the 1/8, and I was just hitting 6th at the traps when I was trapping in the 110 range. I programmed it out of the ECM to shave a few hundredths off my ET, and I was still under 3500 RPMs in 5th at those speeds. Are you running some really small tires or a gear ratio lower than 3.73s?

Josh there the 275/55/16 they say 28" but I think there really 27.80"
watch the run a few times and count the shifts , seems to go thu them fast I know its liking the high rpms carry that thru the 1/8 more and then if it went to 6ths towards the traps more I think it would help.