Search results

Search the forum Search Articles
  1. LB719

    Lift pump pressure @ higher elevation..

    Awesome, thanks a bunch.
  2. LB719

    Lift pump pressure @ higher elevation..

    Just made the trip from SoCal (sea level) to Colorado Springs (6000+ft) and I noticed that my lift pump gauge showed a 3psi drop (6psi from 9psi). This happened the last time that I came out here as well. Is this just a drop on the gauge due to the barometric pressure being about 3psi lower up...
    • LB719
    • Thread
    • Replies: 2
    • Forum: LB7
  3. LB719

    Weight Lifting/Body Building/Strong Man/Training thread

    Thanks, it kind of sucks because there is no pain at all so I don't know what movements could be hurting it. That's why I had to have the surgery again, I overworked it the first time and developed excessive scar tissue.
  4. LB719

    Weight Lifting/Body Building/Strong Man/Training thread

    Just had surgery on my chest again, I'm down for a month. I finally got back up to my old strength and now it's going to go away again. These deployments/work ups have been destroying my gains and now this surgery. I did however go to the gym yesterday and hit calves and some cable bis and tris...
  5. LB719

    Kryptonite UCAs & Steering Kit

    I heard that they were coming out with LCAs as well, I eventually want to replace my my UCAs, LCAs, and knuckles. My truck came from Wisconsin and the previous owner didn't keep the salt washed off, so it has some pretty bad pitting and decay on them. I cleaned them up and painted them but they...
  6. LB719

    Built Engines ready to ship

    Thanks!
  7. LB719

    Advice on Turbo/Fuel Setup...

    I plan on getting the motor built by SoCal here pretty soon, afterwards I am looking at doing 100% over injectors, Dual CP3s, and a S475 over the 64mm IHI that is on the truck now. I am looking to get into the high 700 to low 800hp range. Any suggestions to the setup to get me there would be...
    • LB719
    • Thread
    • Replies: 0
    • Forum: LB7
  8. LB719

    Built Engines ready to ship

    Dustin, Looking for a good DD setup (600hp) and the occasional 8-900hp at the track.
  9. LB719

    Long crank after lift pump install

    Is it possibly sucking air somewhere? Mine was at the filter and it would crank for a few seconds before it fired, I re-lubed the seal and all was well.
  10. LB719

    30 over injectors on stock cp3

    I'm running the 30 over/ 64mm setup you are talking about, if you are looking to make around 600hp and have close to stock driveability then it is a good setup. Initially, I went with a 64mm IHI for emissions reasons (visual inspection) out here in communist California. Now that I am getting the...
    • LB719
    • Post #19
    • Forum: LB7
  11. LB719

    lift pump

    AD 165 w/ CAT filter
  12. LB719

    mpg not what I expected

    +1, running at 70mph vice 80mph is close to a 2 mpg difference for me, when my truck was bone stock i would average around 15 mpg city/17-18mpg highway. I can touch 20mpg on long highway runs but that is not using cruise control and really paying attention to my speed. Do a balance rate test and...
    • LB719
    • Post #12
    • Forum: LB7
  13. LB719

    Kryptonite UCAs & Steering Kit

    Looks Great, the Kryptonite Stage 3 kit is going to be my next purchase.
  14. LB719

    2003 Chevrolet 2500hd silverado

    LB719 submitted a new Showcase Item: 2003 Chevrolet 2500hd silverado Read more about this showcase item here...
  15. 2003 Chevrolet 2500hd silverado

    2003 Chevrolet 2500hd silverado

    -MikeL Trans -Efi Live -Billett 64mm IHI -30% overs -AD165 -AEM BruteForce Intake -ProFab intake horn/downpipe -5'' Flo Pro Straight Pipe -PPE Gauges -Edge CTS
    • LB719
    • Showcase item
    • Category: Main
  16. LB719

    Intro

    Hey Guys, I jumped over here from another forum, seems like there is a lot more info and less BS here. I am from Colorado Springs, CO but currently stationed on Camp Pendleton. -Mike-
Top Bottom