Search results

Search the forum Search Articles
  1. coalroller83

    Cylinder wall honing surface finish & ring gap

    Thanks!
  2. coalroller83

    Af cam wiring?

    I agree! I repinned mine. I just felt better going that route, rather than in tuning. So... What if the wrong tune gets flashed in by accident...? Just my OCD taking over![emoji4]
  3. coalroller83

    What compression ratio?

    I'm running 15.5 Fingers Ovals in my build. I can't wait to get it fired up![emoji12] LB7 CC SB, 10mm Exergy, 30% injectors, AirDog II 200, billet Stage V Trans, River City 66/74 IHI, Turbonetics Intercooler, PPE up-pipes/manifolds, complete engine ARP studded, Flex-a-Lite fan, AlliLocker...
  4. coalroller83

    Cylinder wall honing surface finish & ring gap

    Does someone have the RA number? I'm running Fingers cast pistons, with steel rings. LB7 CC SB, 10mm Exergy, 30% injectors, AirDog II 200, billet Stage V Trans, River City 66/74 IHI, Turbonetics Intercooler, PPE up-pipes/manifolds, complete engine ARP studded, Flex-a-Lite fan, AlliLocker...
  5. coalroller83

    LB7: Custom intakes and intercooler tubes

    Jason Wehrli can make you one... I have one of his on my LB7. LB7 CC SB, 10mm Exergy, 30% injectors, AirDog II 200, billet Stage V Trans, River City 66/74 IHI, Turbonetics Intercooler, PPE up-pipes/manifolds, complete engine ARP studded, Flex-a-Lite fan, AlliLocker, E-Locker, TrueTrac, topped...
  6. coalroller83

    657hp 1089T With a IHI

    That's a solid run! I'm running the same charger, with 30% nozzles... 666hp, 1287 tq.
  7. coalroller83

    Vband clamp nut size?

    11mm is the OD. Not positive on the thread size... 6mm?
  8. coalroller83

    LB7: Whos got used LB7 aftermarket parts

    What all are you looking for? LB7 CC SB, 10mm Exergy, 30% injectors, AirDog II 200, billet Stage V Trans, River City 66/74 IHI, Turbonetics Intercooler, PPE up-pipes/manifolds, complete engine ARP studded, Flex-a-Lite fan, AlliLocker, E-Locker, TrueTrac, topped off with EFILIVE, to name a...
  9. coalroller83

    LLY: Some goods

    Agreed. I'd drop to the idler between the a/c compressor and your dual pump, run from the fan idler straight over to the p/s pump. LB7 CC SB, 10mm Exergy, 30% injectors, AirDog II 200, billet Stage V Trans, River City 66/74 IHI, Turbonetics Intercooler, PPE up-pipes/manifolds, complete engine...
  10. coalroller83

    The build is a GO!

    I have a set of SoCal beehive springs, titanium retainers, and Merchant's chromoly pushrods I'd sell you! New, in box. LB7 CC SB, 10mm Exergy, 100% injectors, Wagler Comp Street ported heads, Empire Stage 2 AF cam, Fingers cast/coated Pistons, Carrillos, AirDog II 200, billet Stage V Trans...
  11. coalroller83

    The build is a GO!

    Hmm... I'd like some input as well, on the rod bolts. I have a set of Carrillo's here, that I was debating on putting the ARP's in.... LB7 CC SB, 10mm Exergy, 100% injectors, Wagler Comp Street ported heads, AF cam, Fingers cast/coated Pistons, Carrillos, AirDog II 200, PPE Stage V Trans...
  12. coalroller83

    Allison drops out of gear

    Sorry for the delay in posting! I bought another t-case, and it works fine now. Once I have time, I'm going to tear this one down, and figure out what happened. Thanks for all your input! LB7 CC SB, 10mm Exergy, 30% nozzles, AirDog II 200, PPE Stage V Trans, EFILIVE DSP5, Turbonetics...
  13. coalroller83

    Oval Chamber Pistons

    Subd LB7 CC SB, Stroker CP3, 30% nozzles, AirDog II 200, PPE Stage V Trans, EFI Live DSP5, Turbonetics Intercooler, 66/74 IHI, to name a few... :)
  14. coalroller83

    Allison drops out of gear

    Transfer case is freshly rebuilt with a pump rub kit, all new bearings, chain, oil pump, speed sensor, encoder motor, and seals. LB7 CC SB, Stroker CP3, 30% nozzles, AirDog II 200, PPE Stage V Trans, EFI Live DSP5, Turbonetics Intercooler, 66/74 IHI, to name a few... :)
  15. coalroller83

    Allison drops out of gear

    Ok... So I pulled the entire wiring harness out, unwrapped it, and tested each wire in the harness, and they all checked out with a continuity tester. I also physically inspected each wire... no kinks or signs of abrasion anywhere!! TCM is not showing any codes at this time, but it's still...
  16. coalroller83

    Allison drops out of gear

    Thanks guys! I'll keep you posted. LB7 CC SB, Stroker CP3, 30% nozzles, AirDog II 200, PPE Stage V Trans, EFI Live DSP5, Turbonetics Intercooler, 66/74 IHI, to name a few... :)
  17. coalroller83

    Allison drops out of gear

    You're thinking a broken wire? Sent from my iPad using Tapatalk
  18. coalroller83

    Allison drops out of gear

    Initially, no. Yesterday I checked again, there was 3 "U" codes. I don't remember the numbers, but I'll get them. LB7 CC SB, Stroker CP3, 30% nozzles, AirDog II 200, PPE Stage V Trans, EFI Live DSP5, Turbonetics Intercooler, 66/74 IHI, to name a few... :)
  19. coalroller83

    Allison drops out of gear

    Also, the Neutral Safety Switch, internal wiring harness, pressure switch manifold, solenoids F, D, and E have been changed. LB7 CC SB, Stroker CP3, 30% nozzles, AirDog II 200, PPE Stage V Trans, EFI Live DSP5, Turbonetics Intercooler, 66/74 IHI, to name a few... :)
  20. coalroller83

    Allison drops out of gear

    So I'm driving my truck along (just maintaining speed) and it acts like it went into neutral! I left off the throttle, and it immediately 'grabbed' again. It will not do it under power, or accelerating, just when your under maybe 20% throttle. No codes in the ECM or TCM. I have a manual TC...
Top Bottom