Search results

Search the forum Search Articles
  1. Tony Burkhard

    Mild Y-Bridge Plates

    I dont think you will get the LB7 runners to work with a VVT. I will know in a week or so about the Cali to Fed LB7 runners.
  2. Tony Burkhard

    Mild Y-Bridge Plates

    The LB7 runners are not restricted by the turbo area like the VVT motors. You will find that the VVT motors have hotter #7 and #8 cylinders do to this restriction. Yes the LBZ/LMM runners have a larger hole but we can feed the LB7/LLY runners with the same size plumbing and not have the air...
  3. Tony Burkhard

    Mild Y-Bridge Plates

    I could do that.
  4. Tony Burkhard

    Mild Y-Bridge Plates

    The intake runners on the LB7 are better flowing than the LLY and the LLY are better than the LBZ.
  5. Tony Burkhard

    Mild Y-Bridge Plates

    I have them in aluminum. And the LB7 intakes flow way better than the LBZ.
  6. Tony Burkhard

    Project DH 3.0

    Shoes fit....
  7. Tony Burkhard

    Off Season Sled Pulling Mods

    The new shoes fit.
  8. Tony Burkhard

    Leveling kit pulling?

    Get a four inch lift, its what I have done for years with not a single broken front end part.
  9. Tony Burkhard

    All Season Centerlink Brace?

    leveling kit will get you everytime. Even if there turned down there still higher than factory and will kill the front end in time and looks like it got one the first time. Waiting to find out if the idlerarm bracket was bent. Here will be a good thread...
  10. Tony Burkhard

    Warning to any vendors with credits cards online

    I got hosed from some S&H units ordered from Canada. My CC company would not stand behind the charges.
  11. Tony Burkhard

    All Season Centerlink Brace?

    I would have to bring my truck in again and look it over, its been three or four years since i tried.
  12. Tony Burkhard

    All Season Centerlink Brace?

    Hope you dont have a leveling kit or have the t-bars cranked all the way up.
  13. Tony Burkhard

    All Season Centerlink Brace?

    Remove the idler arm nut and pitman arm nuts that are found at you center link, install bracket onto the studs with the plastic against your front diff. Locktite your nuts and reinstall them and torque to spec. Make sure your steering can turn from stop to stop without interference.
  14. Tony Burkhard

    2 sizes of U-Joints?

    I know all the manual trucks had 1480's and 2007 NBS and up have the 1480's in all of them. Most everyone up-grades to my 1480 billet yokes if they had the 1410 in there pulling truck.
  15. Tony Burkhard

    2 sizes of U-Joints?

    Lets look at the door tag and see were they are built. I think i saw a difference from Canadian built and US built.
  16. Tony Burkhard

    Tranny Opinion?!?

    I could get one whipped up for you and on its way....
  17. Tony Burkhard

    Project DH 3.0

    Well you know that is to be figured out yet. I think we will run around 10 to 1 but im sure we will be starting out around 12 to 1.
  18. Tony Burkhard

    Off Season Sled Pulling Mods

    Here is a pic or two.
  19. Tony Burkhard

    Project DH 3.0

    Here is a few pictures.
  20. Tony Burkhard

    Off Season Sled Pulling Mods

    I had a lot of fun kicking ass at Dekalb but it is crowded there, it's always been six inches of mud and snowing... Lol
View older results
Top Bottom