Search results

Search the forum Search Articles
  1. SoCalMike

    Turn signal staying lit up when headlights on

    Yes. And the led flasher. I have a resistor in the one of the front 194. But it should work the same if on The rear. 3 resistors and the led flasher fixed my problems.
  2. SoCalMike

    Turn signal staying lit up when headlights on

    From my reading the led flasher is only good for two LED bulbs in the turn signals. The flasher was made so people with led trailer light don't have problems. That is why you still need to use two resistors somewhere wired in with the 3157 turn bulbs. Mine works the way I describe and I'm...
  3. SoCalMike

    Turn signal staying lit up when headlights on

    I was having problems with just running the led flasher. With the lights on my dash turn signals we're on but very dim. Also my driver's side turn signal in the mirror was on and very dim also. When I turned the blinker on it worked normal. As soon as I added resistors to the rear turn signals...
  4. SoCalMike

    Turn signal staying lit up when headlights on

    Also the built in resistors in your switch backs up front might not be the correct resistance. If I were you I would wire up resistors for each turn signal in the tail light and one resistor for the 194s. One resistors will take care of all the 194 bulbs. I used 50w 6ohm resistors. Wire them...
  5. SoCalMike

    Turn signal staying lit up when headlights on

    You need a resistor for the 194s. This is my setup. All LED bulbs in the tail lights. Led turns and 194s up front. Led flasher, resistor wired in for the two rear turn signal LED bulbs and one resistor wired in for the 194 bulbs. I had the same problem as you. When my headlights were on my...
  6. SoCalMike

    Another Mike review.

    I cant say enough good things about Mike L. He really is a great guy and stands behind his work.
  7. SoCalMike

    "OFFICIAL" What did you do to your D-Max today?

    Finished my lift. Well sort of. My torsion bar bolts and nuts stripped. So I need to order them and install. Adjust the front end height so it about level with the rear. Even with the bolts out it's very close to level.
  8. SoCalMike

    "OFFICIAL" What did you do to your D-Max today?

    Having some fun installing my lift today. Cognito 4/6 ntbd and new ball joints. Half way done.
  9. SoCalMike

    Looking for a little more umph when towing

    I agree
  10. SoCalMike

    77' Squarebody

    Must be something with Tapatalk then
  11. SoCalMike

    77' Squarebody

    Nope. They look like they are going to load but nothing.
  12. SoCalMike

    EPA strikes again

    Is the gas aftermarket getting hit just like the diesel aftermarket is?
  13. SoCalMike

    EPA strikes again

    I have heard Magnaflow and Jamo are on the same boat.
  14. SoCalMike

    I dont know with my truck.

    The engine light might be off but you may still be able to pull the codes if the were not cleared for the ecm.
  15. SoCalMike

    Would EGR issues cause trans slip?

    Welcome to the site. It would be best to start your own thread so you can get the help you need. I believe you have two different issues going in and in order to help you we need the codes the truck is throwing.
  16. SoCalMike

    LML Floor Mats = Valet Mode

    I have husky floor mats and just checked to make sure the peddle goes to 100% after reading this. Lol
  17. SoCalMike

    LB7: Power lose and sputtering when up to temp and flooring it

    I agree
  18. SoCalMike

    LB7: Power lose and sputtering when up to temp and flooring it

    Try taking the edge tuner out and see if it does it.
  19. SoCalMike

    New from western PA

    Welcome
  20. SoCalMike

    Goerend "R" or Goerend "DK"

    As the fluid heats up it will expand. Just keep that in mind. At 175f you will want to be at the lower hot hash marks. There should be a line then 3 or 4 hash marks , the the word HOT, then 3 or 4 more hash marks. You will want to be at the bottom hash marks in the middle if possible. That is...
Top Bottom