Search results

Search the forum Search Articles
  1. MAXLLY

    Beginning of the end?

    Thanks Dude, I saw this and didn't originally "get it". Thanks for shining the light.
  2. MAXLLY

    Beginning of the end?

    Not taking negative at all, I am grateful for the input. I hope to be able to return the favor to Salad Guys that have helped through this process.:) I searched for Tomac Racing and Michael Tomac etc couldn't find the site perhaps his site addy is over on the dark site? (DP) Kidding BTW
  3. MAXLLY

    Grillz

    STILLEN has some stuff, both billet and factory looking. Can't speak to the quality and I don't have one... but they keep sending me the freakin' catalogue. Hope this helps.:)
  4. MAXLLY

    Beginning of the end?

    A better deal may be available, i paid $230. They are made by Cognito and i purchased them from NorCal because they had 'em sitting on a shelf and ready to ship. In fact i recieved them the day after i ordered them, it was very nice. What the vendor claimed was going to happen was exactly what...
  5. MAXLLY

    Beginning of the end?

    Yes Sir, I installed the braces several months ago. I considered the straight centerlink until i watched a truck that had one try and park, frankly parking one of these beasts is already difficult for those that aren't accustomed. Adding the straight link appeared to cut down turning radius...
  6. MAXLLY

    Beginning of the end?

    The saga continues.... I was going back through my pictures/videos after New York and noticed that my front wheels are pigeon toe'd, even though i have tie rod braces (thanks Kat). So i replaced them with these MONSTERS. I can't get the camera to link today so i attached an internet...
  7. MAXLLY

    Convertor warranty

    That's the difference between MikeL and ATS. Both good stuff, IMHO. But when you send it to Mike he's the guy who signs for it. At ATS (no fault they are big), it comes in the back door and the guy at the front door doesn't know it. It's there somewhere. Good luck.
  8. MAXLLY

    It's cooold out!

    I am sitting in Laguardia at this moment.... It is SFC!! Spent all week in Manhattan, I had a long sleeve shirt and a real good snowboard jacket (with liner) and the wind cut through it like it was a hanes t-shirt. Long johns needed for a puss such as myself. Don't know how the Eastern...
  9. MAXLLY

    Are you a Democrat, a Republican, or a Redneck?

    Totally agreed, not sure the bastard is worth all the bullets. Slow him down so he can't run away anymore with one bullet. Then stab him with his own knife. Label me a sick bastard as well.
  10. MAXLLY

    sled pullers........start drooling

    Larry, that's EXACTLY what i thought. I could swap a turbo in 20 minutes...pull the trans and have it back in on my feet...i could i could ... Wonder how he ran the harness stuff from bay to cab? extended it all to the back of the truck and then back to the front, at the scissor? Or...
  11. MAXLLY

    Snow flake down rear end problems

    oooo, tone down the tune guys!:rofl: I recently heard of a dragger who "hooked up" at the strip and turned the 3/8" wall housing from the pumpkin!! Jesus Christo that' some grunt, anyway welding the pumpkin to the shaft has become an option, bring the HEAT. Thanks Mike.
  12. MAXLLY

    Snow flake down rear end problems

    Kurt, Sorry to hear about the rear end going out. i didn't see where we established which rear end you had? Corporate or ? Unless the technology and design criteria changed you would be better served with an aftermarket ring/pinion and welding as mentioned by Mike. My opinion, I have an...
  13. MAXLLY

    Gearing

    Interesting thing i learned in the class. The ECM has a gear ratio entry point when changing tire sizes. As well and unknown to me, the ALLY has a gear ratio in mind as well. Hmmm? What happens when they both match? I think i heard that the ALLY is pre set with 4:10 and most our trucks come...
  14. MAXLLY

    Mike L and my SCIV and 1058

    Cool, fast and no smoke. We'll get there, we just have to keep honing in the fuel/rail/boost. Good luck.:)
  15. MAXLLY

    Mike L and my SCIV and 1058

    Yep, I had a very similar experience when Mike did mine. What kind of HP and torque do you have? I should prolly look at your sig... that would tell me. Congrats on the trans! Wait till you go to the track and lean on it, it'll respond nicely. No sig? I see the website in your sig, I...
  16. MAXLLY

    Tight spot rotating engine

    would be cool to have another angle... glow plug all wadded op from compression???? Piched between piston and head?
  17. MAXLLY

    Drag racing with a E Locker?

    Drag racing is good with e lockers. I ordered one, I broke loose with the front tire and only ran a 2.0 60'. I need to say i had 44 lbs in the tires. Use it!! If you don't want it let me know. Ill take it.:)
  18. MAXLLY

    Tight spot rotating engine

    this is a good one. I wake up in the middle of the night sometimes wondering about stuff like this, it's like a nightmare cause you just don't know 100% for sure. The gasket is only 030 max so the tolerance is tighter than mentioned earlier. Mike's click/tap/clunk idea is solid. I have used a...
  19. MAXLLY

    Timeslip Data

    Kat, I have MPH and Time in my profile am I good? If that's not what you want let me know, I will comply, just don't beat me again.:)
  20. MAXLLY

    Beginning of the end?

    Thank you Tooooner Master. I would be a magical brake master if i could fit 16" rotors under a 15" rim huh! Then i could have my pick of slicks.
Top Bottom