Search results

Search the forum Search Articles
  1. MMLMM

    Job hunting...WTF?

    13 resumes for architectural firms 4 resumes for Structural firms 1 interview for an architectural firm 2 weeks before a huge project they were hiring for got shut down so I started looking for anything and applied at various places..turned in 27 applications locally over the last 6...
  2. MMLMM

    Labor rates!

    Changing the cp3...Easy.. Getting to it...thats where the hours come in lol.
  3. MMLMM

    Rail pressure with 2 micron filter....

    I have the factory filter gone. I'm running the cat 2 micron. Yea ever thought about the actually filter flow. I honestly think its my piece o chit fass non filter pump. The pump used to read about 14psi at. Idle but I have since removed gauge when I ditched factory filter. I run quite a bit of...
  4. MMLMM

    Rail pressure with 2 micron filter....

    So I ditched the factory setup and went with my own setup by my lift pump (after it) I am running a 2 micron filter there. I noticed my rail pressure has been low but not sure if I am having lift pump issues again or not. I just swapped on a 12 micron baldwin to test so Ill see if that clears it...
  5. MMLMM

    Help: DSP5 not working

    the 2 wires that go to the ecm are a signal and a ground. You can ground one wherever or in the ecm and the other is the signal. You can swap the wires (doesnt matter which one is ground or signal). Best bet is to ground at ecm pin. Also, the instructions in the efi manual say to use ecm...
  6. MMLMM

    Toxic Diesel Dyno May 1st in St. george, UT

    friday night Midnight Mayhem is I think $10, maybe $15 (cant remember). It will be pretty packed as it always is and plus quite a few trucks are heading down. You should get 3 or 4 runs in if nobody breaks on the track bad. Bring Current insurance, Current registration and be cool. Dont do...
  7. MMLMM

    Toxic Diesel Dyno May 1st in St. george, UT

    Whos going? I know Demetri is going :D Whitetrash21, Me, and maybe another truck will be going. Also Newly is going and bringing a couple guys from CO. We are all racing Friday Night in Las Vegas at Midnight Mayhem, Maybe all of us grab early dinner before we head out to track if you guys...
  8. MMLMM

    New Daily Driver

    We going to see it at any sled pulls competing this year :rofl:
  9. MMLMM

    EFILive Are LB7/LLY DSP pins different than LBZ/LMM??

    Yes. LBZ/LMM are the Bosch Square pins. LB7 and LLY are round. they are each a diff size but cant remember which is bigger/smaller off the top of my head.
  10. MMLMM

    New Office

    yea there is 2 different ones in there. my couch/kitchen table was mine too but I finally got tired of the distractions lol
  11. MMLMM

    New Office

    Dont bullship us Mike...I know what room you were standing in to take that actual pic.... :rofl:
  12. MMLMM

    EFILive Are LB7/LLY DSP pins different than LBZ/LMM??

    LB7 - round LLY - round LBZ/MM - square 3 different Pins.
  13. MMLMM

    New Office

    Lets see what you guys got going on..post pics too :)
  14. MMLMM

    New Office

    turned my spare bedroom into an office awhile back. Thought I'd post pics as I am bored lol. Planning on getting some more good stuff hanging on the wall, and thinking a small couch in the corner and a 20" or so flat screen on the wall. It will be man cave deuce since the garage is setup pretty...
  15. MMLMM

    Question: $ cost for a liscense

    or here, it normally is pretty quick. http://www.efilive.com/index.php?page=shop.product_details&flypage=flypage_EFILive.tpl&product_id=23&category_id=13&option=com_virtuemart&Itemid=56
  16. MMLMM

    Question: $ cost for a liscense

    $99.00, you will need the info from the V2 you will be buying a license for. (serial number and the auth code from within the program).
  17. MMLMM

    Getting ready for DPC!!!!

    :spit: you're doing it wrong...:D
  18. MMLMM

    LMM Dynos 1015 on Fuel

    Jesus F'ing Christ...Thats all I have to say :D :thumb:
  19. MMLMM

    Question: Should I Even Try

    Look online. Rough country sleeves can be had for 35 bucks new. They will work for ya.
  20. MMLMM

    Buyer Beware: Fidel Velasquez/Relentless Performance/murdered out...

    a little background.. I met fidel at a meet a couple years ago (maybe a year and a half) through a friend. He had just got his truck and was excited to see the numbers being run. He wanted to do a bunch of stuff to his truck. My buddies (that lived nearby) helped him get his truck built...
Top Bottom