Search results
-
Lby issues (03 with 05 top end)
I know this is a long shot without any knowledge on the truck but here it goes. Bought the truck needing a trans installed. It’s a 2003 short block with all lly top end. All lly electronics is what it looks like and was told. Lly turbo, ecm, ficm, tcm, engine harness, and harness to fuse box...- quinton
- Thread
- Replies: 11
- Forum: Repower / Transplant
-
LLY: ABS light on
Have a truck with just the ABS light on, no parking brake light. Throws codes for all wheel speed sensors. (pic posted) I’ve checked the two grounds, on frame and cleaned them, checked fuses, checked for broke wires, last thing haven’t swapped is the ABS computer. Was just trying to see if there... -
Barometric issues
Got a lly all stock other than egr removed that is throwing codes P2229 (barometric Pressure Sensor High Circuit) P0234 (Turbo Overboost) and P0100 (MAF Sensor) have tried stock tune and other tunes in it no change, replaced baro, MAP and Maf sensor. (Rescaled Maf sensor and so far that code... -
LMM: Lmm no start from key
Messing with a lmm that will not start, no click or anything. Two codes are p2510 and p2536. Another shop had it and said it would run then DLIS fuse would blow and wouldn’t start. Would replace the fuse and same thing would happen. Now no start period. New Tcm and ignition still nothing. Now... -
LLY: Need stock file for lly
Anyone have a stock file for this truck here is vin. 1gchc23235F866931. 2005 lly crew cab short bed 2wd cloth seats. Thanks.- quinton
- Thread
- Replies: 5
- Forum: Tune Library
-
LML Lml fuel related issues.
Working on a 2012 lml with brand new 12mm pump and 100% injectors. Truck wouldn't build rail pressure for a bit but finally did and ran it for about 30-40min then it died. No knocking or funny sounds while running,little bit of white smoke, could be from stock tune in it. Checked the amount of... -
LML Lml high rail pressure
Got 2011 lml I just built with a 12mm cp3. Another guy installed the motor and crossed the rail sensor plug with the FPR plug. He said got a new FPR and installed it and never plugged it in. Well after I swapped em I got the truck running but it's maxed out on rail pressure plugged in or...- quinton
- Thread
- Replies: 9
- Forum: Duramax Engine Building
-
LLY: Turbo rebuilders
Looking for a rebuilder for my s475. I'd like to make it into a 72 so I can finish my triple setup. I'm located in Texas but don't mind shipping if they are good. Also are they able to just trim the compressor whee down to a 72 mm and I just purchase a new housing? -
Busted Danville pinned pump
So just put. Danville pinned water pump in the truck be made one or two passes on tune three and then this happened!? Now the pin is somewhere in the motor. Has anyone else had this happen?- quinton
- Thread
- Replies: 59
- Forum: Danville Performance
-
Hvac foam seals
Was wondering if anyone knew a place to get all, or a kit, of the foam seals for the hvac unit. Need to replace my evap. and want to do everything I can while I have it out.- quinton
- Thread
- Replies: 5
- Forum: Appearance & Detailing
-
LBZ: Cheap FPR!? $25
Anyone ever seen these before or used em!? I was just looking around on eBay and caught this and had to click it. Not much info on it but I wouldn't trust it... -
LLY: S475 with spray
Just curious what some of yalls times have been with a single s475 and spray. Would like to know how much spray, tires used, weight, and size of truck. Also anyone ever weighed the backseat, and front seat of a crew cab? I got bored last weekend and pulled them out and plan on going to a event...- quinton
- Thread
- Replies: 7
- Forum: Drag Racing
-
LLY: Lly overheating
So my lly started overheating recently. Built motor and the water pump is welded on both sides. I've replaced radiator, sensor, and cap. I pulled the water pump first and everything looked good on it. Not leaking coolant and no bubbles in over flow no collapsed hose or any sign of headgsskets... -
LLY: Light wheels for the strip
Was wondering what some of you guys are running for wheels on the drag strip. What offset and what is the weight of them? Pics would be nice too if like black. I tried looking through here but couldn't find a thread on wheels, I know there's one here somewhere. With my current setup I can't cut...- quinton
- Thread
- Replies: 25
- Forum: Appearance & Detailing
-
Texas nationals who's going?
Anyone going this weekend? Hopefully the weather holds off.- quinton
- Thread
- Replies: 12
- Forum: National Events
-
New race truck build
So my father n law and I picked up this 05 for dirt cheap. Motor is locked up but the plan is to put my built motor and trans in it and put my father n laws 49 Chevy body on. It will be 4 linked, coil overs, torsion bars removed, and converted into a short bed. Should be. Fun truck once we are done!- quinton
- Thread
- Replies: 15
- Forum: Smoke Signals
-
Injector testing in Texas
Anyone know of a few places in Texas that tests injectors? Preferable around ft worth area but if not that's fine. -
4th to 5th hang up
Having a problem where at any throttle percentage going into 5th the truck hangs for a split second then shifts. Just started happening a few days ago. Only thing I've done was put a cat fuel filter on my air dog. No codes at all. Drives great other than that small Hiccup. Any ideas? -
Fresh build over heating
Just finished rebuilding my 5 speed with gmax5 kit with reybestos clutches, mikes pressure spring two shims, mikes valve body springs, new valve body, new NSBU, and grinded a little on my converter valve for no knock down. ( I grinded a small amount being I have transgo parts in it) when I...- quinton
- Thread
- Replies: 47
- Forum: Mike L's Trans Talk
-
Allison parts.
If this needs to be moved mods go ahead. I'm looking for someone that can get me all Torrington bearings and thrust washers for my 5 speed. I got my clutch kit from suncoast but they said they couldn't get me the rest. Pm if you can get these parts thanks.