Search results

Search the forum Search Articles
  1. Bbuchanan11

    2017 intermittent rough idle

    Hey guys I have a 2017 2500 with just under 18k on it.. every once in a while at a stop light I can feel it idling different. I’ve done some research and read a lot about the injector harness being junk, the truck runs great no CEL. I only have access to snap on scanners could it possibly show a...
  2. Bbuchanan11

    Well there goes my chances of 9s this year

    Went to the track Saturday and didn’t end well… happened right at the top end trapped 133mph made for a very sketchy stop.. had mahle Motorsports cast pistons corrillo rods and Callie’s crank. Guess I have a winter project now.
  3. Bbuchanan11

    Lexan back window

    Does anyone know where I can get a pre cut Lexan back window for the 00 to 07 trucks? I remember years ago I thought dhd or alligator had them on their site but I can’t find it now. I found one site that says requires trimming just seeing if you guys know of a better option…. Thanks
  4. Bbuchanan11

    Transmission vent cap

    Hey guys I was wondering if anyone could tell me if the trans vent for an 06 threads in or are they pressed in? I’d like to remove the factory one and find an A N fitting to thread in and run a hose higher up somewhere. Or will I have to just remove the cap and attach the hose to what’s left...
  5. Bbuchanan11

    Bed mounted trans coolers

    I have the trans out of my truck and I know metal went through the coolers.. my question is if I would put 2 derale coolers with fans in the bed would I be able to street drive the truck and race it if I got rid of the factory exchanger in the rad and cooler?
  6. Bbuchanan11

    Controlling boost while spooling

    Ok guys this might be a dumb question but when I’m spooling at the line I hit a certain rpm where the boost just wants to take off and constantly push through the brakes. It makes for very inconsistent staging and if I’m not right at that point when launching it almost bogs down.. my question is...
  7. Bbuchanan11

    Need some 60ft advice

    Took my truck to the local track For the first time since last year and made a bunch of changes. They were running a funny car circuit so it was 1/8th mile and traction was not an issue. I ran a 6.73 @ 106 with a 1.62 60 ft I have qa1s single adjustable all the way around with coil overs in the...
  8. Bbuchanan11

    Custom made intercooler pics

    had all kinds of trouble blowing boots off so a buddy of mine just decided to build me a new intercooler and new pipes using vibrant clamps what do you guys think?
  9. Bbuchanan11

    Fuel cell questions

    Hey guys not sure exactly where to put this thread but I plan on doing a fuel cell this winter. I’ve researched as much as I can I have the fuel pump feed and return figured out, I’ve read that I can get a cell with a certain level sensor to work with factory gauge after re scaling. My questions...
  10. Bbuchanan11

    What gear do you guys usually trap a 1/4 in?

    Finally got my truck to the track for the first full run on it (broke the crank last year) I always put it in manual and select 5th to keep it out of 6th.. I almost swear it was on the rev limiter going through the traps granted this truck is faster then my last one but I always raced it keeping...
  11. Bbuchanan11

    6an feed line too small?

    Not sure where to put this but it’s for a drag truck. I’m trying to clean everything up I want to make the feed lines for the cp3s an line. I got 8an going in to 2 6an lines for the feed lines. Looking inside the 6an fittings they look pretty small will they work or no? Thanks in advance
  12. Bbuchanan11

    Need some help p0336 p0606

    So I took the truck in my sig to the track for the first time.. first run right after 1/8 miles it cut out and shook violently then would just lope real bad.. idles fine now but shakes when you rev it and the tach jumps all over the place threw a p0339 and p0606 also a p2761 which is I trans...
  13. Bbuchanan11

    noise with door open or hood open

    I’ve tried to google this but what is the rod on the turbo that moves when you open and close the doors or open the hood? And why does it do that?
  14. Bbuchanan11

    Heater hoses at heater core with twins

    I picked up a truck with what seems to be a custom set of twins. Previous owner cut the ends of the heat core off I'm guessing because the hot side pipe would not fit.. I'm planning to take dash out and put a new heater core in it so I can obviously have heat in the truck. Can some of you guys...
  15. Bbuchanan11

    Does anyone know this truck?

    Hey guys not sure if this is the right place for this but I just picked up an 06 gmc twin turbos dual fuelers built motor/trans. As I'm going over it and fixing some stuff I noticed some of the info I was told isn't very accurate. I'm going to post a link of a picture of it because I don't know...
  16. Bbuchanan11

    Help p0659

    I have a 2006 that keeps setting a p0659 I cleaned and greased 20 pin connector no difference... I tested the voltage at tcm and at the 20 pic connector both showing 12 volts. I see that it should be 6 volts, any suggestions? Thanks
  17. Bbuchanan11

    Highest hp on a single stg2 3794?

    Hey guys just curious as to some of the highest numbers you have seen out of the 3794s.
  18. Bbuchanan11

    Painted my head lights

    Took them apart in the oven and my buddy who paints for bmw did the paint work
  19. Bbuchanan11

    Need help problems after cp3 install

    Just put a new cp3 on my truck started up fine after cranking for a few seconds but the check engine light came on oil pressure gauge will not move and the fuel gauge also will not move throws a bunch of codes for oil pressure fuel level senser a/c mass air flow senser and maybe more can't think...
  20. Bbuchanan11

    Anyone have trex up pipes?

    I was looking on eBay for some up pipes and see that trex now offeres them for 438 a pair. I tried doing some searching but I haven't found any threads on them.
Top Bottom