LBZ: Cracked piston

[hipp11B]

Welp guys my worst fears were confirmed trucks been down for 7-8 months with what was originally suspected to be a bad injector, however I had a suspicion that I had something else going on. Long story short army has kept me to buisy to mess with it for the last 7 months so it sat. Bought a cheap endoscope off eBay a few weeks ago now that I have some time on my hands (going through meb board) and #6 piston has a nice crack (shitty picture of a picture) truck has been my pride and joy for the last 5 years but she will now be sitting for awhile until I can come up with the funding to build her. Not gonna go full retard aka. Forged pistons, ext. As it will be my DD I'm pretty dead set on fingers pistons herd a lot of great things. Any input is welcome

Sent from my HTC6525LVW using Tapatalk

 

[ripmf666]

If we can help we have a few bundles that would work for you.
Carrillo rod bundle. 4,700.00 shipped + 725.00 using Finger oval Pistons.
http://creaturesofthenightperforman...-Carrillo-Rods-Pistons-Bearings-P3292161.aspx

Brian Crower Rod bundle. 4,100.00 shipped + 725.00 using Finger oval Pistons.
http://creaturesofthenightperforman...an-Crower-Rods-Pistons-Bearings-P5172414.aspx

Carrillo Rod bundle less piston kit. 3,150.00 shipped also do same bundle with Brian Crower rods for 2,650.00 shipped
http://creaturesofthenightperforman...ul-Gasket-Set-H-Series-Bearings-P3579197.aspx


Mahle race cast bundle less rods. 2,570.00 shipped + 725.00 using Finger oval Pistons.
http://creaturesofthenightperforman...it-with-Mahle-Race-Cast-Pistons-P2372186.aspx

Mahle OEM bundle less rods. 2,150.00 shipped
http://creaturesofthenightperformance.com/Duramax-LB7LLYLBZLMM-Stock-Rebuild-Kit-P3604882.aspx

 

[hipp11B]

Thanks ripmf666! I was actually looking at your bundles last night once I get the funds togeather will probably go with your carrillos and fingers bundle!

Sent from my HTC6525LVW using Tapatalk

 

[Hot COCOAL]

Thanks ripmf666! I was actually looking at your bundles last night once I get the funds togeather will probably go with your carrillos and fingers bundle!

Sent from my HTC6525LVW using Tapatalk

Henry likes it when his bundle gets checked out...he likes it even more when you get your hands on it
:roflmao:

JK
Henry is good peeps and knows what's up, he will take good care of you
Beautiful :chevy: truck BTW
atriot:

 

[hipp11B]

Haha thanks bro

06 lbz built trans, airdog2, Ppe gauges, efi by eisenhart diesel, arp head studs, Danville billet 68mm 4094, custom traction bars, fuel rail shim, s&b intake, 5 inch mbrp 7 inch stack, 20x12 tis, Goodyear duratrac my.

died - Feb 2015

 

[Awenta]

Build it right the first time. Fingers pistons are a good choice.

That's one pretty truck you've got there

Sent from my SM-N910V using Tapatalk

 

[hipp11B]

Thanks man and for sure!

06 lbz built trans, airdog2, Ppe gauges, efi by eisenhart diesel, arp head studs, Danville billet 68mm 4094, custom traction bars, fuel rail shim, s&b intake, 5 inch mbrp 7 inch stack, 20x12 tis, Goodyear duratrac my.

died - Feb 2015

 

[hipp11B]

Started the process of getting her yaked out today did as much as I could until my back had enough lol plan is to get it ready to pull then next week when I get my cherry picker all I gotta do is chain and yank! P.s if I could go back and kick young me' sass for all that mudding I use to do I would ****ing filthy lol


Lbz, built trans, efi by Eisenhart diesel, Danville 68, full egr delete, mbrp down pipe, 5" mbrp to 7" stack, ppe guages, custom traction bars, airdog2 165, ppe fuel rail mods, s&b, age blade runner, Arp head studs..died March 2015

 

[Hot COCOAL]

When you yank the engine, put load on the hoist and then place a jack under the bell housing and tilt the bell housing up, this will help the engine slide away from posts on the Bell housing and also help the engine mounts to release, least that was my experience :thumb:

And then remember to do that again upon install

 

[hipp11B]

When you yank the engine, put load on the hoist and then place a jack under the bell housing and tilt the bell housing up, this will help the engine slide away from posts on the Bell housing and also help the engine mounts to release, least that was my experience :thumb:

And then remember to do that again upon install

Thanks for the info bud


Lbz, built trans, efi by Eisenhart diesel, Danville 68, full egr delete, mbrp down pipe, 5" mbrp to 7" stack, ppe guages, custom traction bars, airdog2 165, ppe fuel rail mods, s&b, age blade runner, Arp head studs..died March 2015