Search results
-
D
Help. Proper injector cup install.
Is there a thread/video for injector cup/injector installation? The heads are out of truck. Motor is being assembled and next step is the heads. Any help will be appreciated.- DuraLb7Max
- Thread
- Replies: 10
- Forum: LB7
-
D
Help! Piston Ring setup
Tell what y'all think about this. Pistons were dipped or sprayed at the machine shop I got them cleaned up at. Is this ok to have that coating on there?- DuraLb7Max
- Post #6
- Forum: LB7
-
D
Help! Piston Ring setup
That there is actually 3 rings on the piston. Alldata showed a 4 ring setup for some reason, but I just wanted to make sure.- DuraLb7Max
- Post #5
- Forum: LB7
-
D
Help! Piston Ring setup
- DuraLb7Max
- Post #2
- Forum: LB7
-
D
Help! Piston Ring setup
Rebuilding my Lb7. About to assemble the pistons. I need help confirming I have them set right. Mahle pistons rings and I believe there are the three piece set. I will load a pic.- DuraLb7Max
- Thread
- Replies: 8
- Forum: LB7
-
D
Assembling motor. Need answers!!
Here is a pic of the rings on a piston. Making sure they are on correctly.- DuraLb7Max
- Post #63
- Forum: LB7
-
D
Assembling motor. Need answers!!
Confirmation? Mahle piston rings The mahl piston ring for my lb7 is a three piece set correct?- DuraLb7Max
- Post #62
- Forum: LB7
-
D
Assembling motor. Need answers!!
Ordered new main/rod bolts. The torques spec for the main bolts are 72ft.lbs. then 97ft.lbs. after torquing to 72 I losen them back up then torque too 98? Of course in the correct sequence. Just making sure you torque then losen.. then torque again? Or can you torque to 72 then straight to 97???- DuraLb7Max
- Post #55
- Forum: LB7
-
D
Assembling motor. Need answers!!
What bolts need to be replaced that are torqued to yield? Rod bolt? Head studs is all I ordered regarding bolts.- DuraLb7Max
- Post #51
- Forum: LB7
-
D
Assembling motor. Need answers!!
They are not new... Original mains have about 200,000 on them- DuraLb7Max
- Post #47
- Forum: LB7
-
D
Assembling motor. Need answers!!
What is recommended to put on your main bolts before finally assembly? Arp torque lube?- DuraLb7Max
- Post #45
- Forum: LB7
-
D
Assembling motor. Need answers!!
Everything is in spec just had it measured. Went to a local shop just to make sure. Plastigaged also. Everything is good.- DuraLb7Max
- Post #44
- Forum: LB7
-
D
Assembling motor. Need answers!!
Yes stock rebuild. I had the heads redone and block honed crank checked...30 over injectors lbz cp3 fass 150 with efi live. That's all for performance. Arp studs. I'm just firing off here sorry if not in order. Obviously none that will take place until the crank is perfected. I'm not moving...- DuraLb7Max
- Post #42
- Forum: LB7
-
D
Assembling motor. Need answers!!
- DuraLb7Max
- Post #38
- Forum: LB7
-
D
Assembling motor. Need answers!!
I went back and made sure the girdle side and cap side were dry along with back side the bearings and reinstalled the bearings now I'm going to check the clearances. I will start to load pics as I go along- DuraLb7Max
- Post #37
- Forum: LB7
-
D
Bolt diagram!
The two for the thrust plate bolt. I got some from a dealership.- DuraLb7Max
- Post #12
- Forum: LB7