Search results

Search the forum Search Articles
  1. sweetdiesel

    Post pics of your gauge/monitering setups

    Not sure if HP has the table to rescale boost sensor or not? If it does you can use supplied scaling or Microsoft Excel. Basically 5 Ma is 100 psi and 0 is 0. I used a air compressor to scale mine but it's rather simple
  2. sweetdiesel

    Post pics of your gauge/monitering setups

    You can use a lb7 oil pressure sensor(not a 01) or most aftermarket gauge companies issipro for sure sell just the sensor and you can use that You would have rescale the boost sensor with EFI very simple
  3. sweetdiesel

    Post pics of your gauge/monitering setups

    Swapping sensors on the boost you can read easily 100 psi
  4. sweetdiesel

    Post pics of your gauge/monitering setups

    Race pack solutions IQ3 I also added the Garret speed sensor since this and the box on the left shows rpm and gear I can data log 2- boost Drive press Oil temp and press Trans press and temp egt Gps speed and distance G-force and ambient air temp
  5. sweetdiesel

    Built motor using oil

    Bobos machine and tuning:D Just what I heard on the Internet
  6. sweetdiesel

    Built motor using oil

    Forged or not run the truck hard from a cold start. If you are having issue with rings then start it get it up to temp and then shut it down in a warm Place...... After 45 min start it and throw urbiggest tune In and wot it! Then shut er down. Google break in procedures and you will get the just
  7. sweetdiesel

    Efi tuning who's the best

    I swore you used Moonshine? I tune my own truck, thought that was what EFI was for? but if you can tune my truck better than I can, I buy your tuning and i'll throw in 500 bucks.
  8. sweetdiesel

    hard block

    I don't have any issue with temps biggest thing was removing stock oil cooler Mine is half filled
  9. sweetdiesel

    Big Triple or Big Twins

    . I love my PBK What has your turbo done that's so special:D
  10. sweetdiesel

    2005 lly wont start... HELP

    Pull the glow plugs and crank it over, you should be able tell if there is no/ low comp on one or more cylinders, heck even just stick something in the hole like some gum Ya it sounds cheap but if ya don't have any compression A bent push rod would prob make a noise
  11. sweetdiesel

    Top 53 RWYB Street Legal List

    can i ask why 53? and not 50 or 60?
  12. sweetdiesel

    2005 lly wont start... HELP

    It turns over by hand, freely?
  13. sweetdiesel

    What compound setup for 1000-1100whp

    100 psi is really good! How fast does it spool? Im assuming really quick being a VGT,Im just curious as to what made the decision to go VGT? I know this is a different animal but my stock lly had close to 3:1 DP on stock tuning, but this was at lower RPM not at peak is this a case with the...
  14. sweetdiesel

    2005 lly wont start... HELP

    Find someone with a scan tool and check cranking fuel pressure, make sure you have atleast 12.7 volts while cranking. you can pull all the glow plugs and crank the truck over and check for fuel coming out of the cylinders this indicates a stuck injector and will cause low fuel press while...
  15. sweetdiesel

    Time To Start My Reg Cab Short Box Build

    My truck weighs 5330lbs and its 4x4.I cant loose any more without fibre glass and lexan and i need to add a cage from the standard roll bar. I would think you could get your truck down to 4700lbs with some serious reduction.
  16. sweetdiesel

    NEW Top 25 Stock rules poll

    Gut it and push the stock motor as far as you can! Be careful of them sharp edges though! Tough list Josh but IMO the best thing about the old list was seeing how far a stock internal motor can go Personally I think if guys could simply post the weight of the vehicle it would give other guys...
  17. sweetdiesel

    Question: Ditching the fuse box?

    Ben I posted a pic of the fuse box ditched and under the dash. I'm sorry that this bothers you? You never said to me or the OP that we couldn't have a helping hand? I've changed my mind, I would prefer Bud light please ship promptly as I'm starting to sober up:D
  18. sweetdiesel

    Question: Ditching the fuse box?

    Yup waaaaay fasta Where's my beer?
  19. sweetdiesel

    Question: Ditching the fuse box?

    listen up bitter Benny, I never said it would take HIM 18 hrs I simply said that's how many hours it took for mine. You have never done this yet you give a time frame ??? And yes you still owe me beer
  20. sweetdiesel

    cracked piston

    Curious of how you interpret that?? I'm no expert but yes it looks like a injector issue as in Ryan injected much fuel for a POS piston lol It's a common problem haha
Top Bottom