Search results

Search the forum Search Articles
  1. Bonestock

    PPE Centerlink

    Thanks man. I think my CL is okay the way it is because the wedges that came with the lift. I probably need to lower the truck and put smaller tires on it. Damn it!:mad:
  2. Bonestock

    PPE Centerlink

    Done deal. Thanks Dan.
  3. Bonestock

    PPE Centerlink

    I was actually going do this but my spindle holes are tapered from the bottom up. The tie rod would barely poke thru due to the taper being opposite.:(
  4. Bonestock

    PPE Centerlink

    Man I looked the thing over and thought I had it right. The top of the CL also has recessed area along with a small counter sunk area. I do have some wedges that slide up into the cl that came with my procomp lift. If you are looking straight at the truck sitting on the floor you can see the...
  5. Bonestock

    PPE Centerlink

    a few more pics.
  6. Bonestock

    PPE Centerlink

    A couple of pics of the procomp heim supports connected to the centerlink.
  7. Bonestock

    PPE Centerlink

    I will take some pics here in a bit and post.
  8. Bonestock

    PPE Centerlink

    Will do on the bars. I had em turned up a bit for tire clearance. Looks like the truck may get a set of 33x12.50x20's if I have too.
  9. Bonestock

    PPE Centerlink

    They look pretty flat. Not much of an angle and bars are down a ways not all the way.
  10. Bonestock

    PPE Centerlink

    Well no pics for now. I finished the project and was real excited to test out the 4wd launch. I am a bit disappointed in that part. When I try to launch @ 10lbs of boost the tires spin and truck hops and pulls side to side. I was really hoping to aid that. If I launch @ 5lbs of boost it left...
  11. Bonestock

    PPE Centerlink

    I will take some more pics and give feed back after I get it put together and aligned. :thumb:
  12. Bonestock

    PPE Centerlink

    Thanks, I am expecting a package to show tommorrow. It will have new Moog Problem Solver Pitman & Idler arm along with a new Kryptonite Idler Pivot and Weld in Brace. ;)
  13. Bonestock

    PPE Centerlink

    Out with the old centerlink and In with the new tommorrow night! :thumb:
  14. Bonestock

    LMM: What turbo to do?

    Hit up Trent @ Epr about the Borg Warner that he just got his hands on. I have heard great things about the Charger. www.extremeprejudiceracing.com :D
  15. Bonestock

    Allison 5sp: trans stuck in third but has reverse

    YOu could try to drop the pan and the valve body. Clean the vb out by removing the valves and spray brake parts cleaner in the passages and blow dry with compressed air. You may have a hung valve but most likely your trans is cashed. I had an lb7 efi setup similar to yours and lets just say 4th...
  16. Bonestock

    468 BBC project truck.

    I have used plenty of sets of Keith Black Pistons and Total Seal rings with Great luck. It all boils down to the machine work on fitting the pistons to the bore correctly. Forged pistons you must run looser clearances for expansion and Keith Black are mainly Hyperutectic pistons that have...
  17. Bonestock

    Happy birthday McRat

    Happy Birthday Pat!
  18. Bonestock

    finally got efi

    You can try it out. Who tuned it? You might want to fill out your sig so we can tell you a bit more. If you have a stock trans and a big tune on your dsp5 depending on how it was programmed you may want to be a bit careful. I once had a race tune with dsp5 on a stock trans and the dsp knob was...
  19. Bonestock

    468 BBC project truck.

    Its real easy you can comfortably cruise with 5 people go 4x4'n tow the boat or camper get 15+ mpg and i guess i havent experienced similiar results in a car yet. The wife & i test drove a new camaro and when we brought it back we had both said this thing is uncomfortable no room and our lifted...
  20. Bonestock

    This should make you GAG!

    :roflmao:
Top Bottom