Search results

Search the forum Search Articles
  1. C

    I need help!!

    Latest update. After messing with it most of Sunday it cleared the code and let me reset the tranny. It shifts fine and runs fine. It doesnt allow me to use the manuel shift mode. And the batteries are only getting 12.7 volts. The display says batteries not charging. I think my problem may be in...
  2. C

    I need help!!

    Its a 2006. Update on it. This morning i checked the tcm harness again for any bad spots. I found none. I hooked it back up and checked for power at the ignition module with the key in run. With the switch out i moved it to start position and the truck started. I let batteries charge for a bit...
  3. C

    I need help!!

    I have spent about 3 hours and havent been able to clear the code. Ive moved the little gear one tooth at a time. Is it possible my tcm has quit? Any way of checking it? If i had one from another truck can i swap it out? Does it have to be same year, tranny, and engine?
  4. C

    I need help!!

    Anyone?
  5. C

    I need help!!

    Can you explain the easiest way to adjust it?
  6. C

    I need help!!

    For about a month i have been getting code U0101. It happens randomly. When its there the truck will crank but wont start. I can clear the code and it fires right up. Its never shifted funny or anything. I read somewhere that its been found to be the electronic module that the key...
  7. C

    I need some advice

    Well it was a long day but my truck is back in one piece. Thanks again for all the help and advice. I would of never thought that noise to be a flexplate!!!
    • Cda55
    • Post #50
    • Forum: LBZ
  8. C

    I need some advice

    Yes i think i found it!!
  9. C

    I need some advice

    Damn are you guys good! Flexplate has cracks all over it. Anybody in CA have one they dont need? I would gladly buy it! Im going to get a tranny built and will go billet then. I need this thing in one piece to get me to and from work!
  10. C

    I need some advice

    On start-up and shutdown its making a pretty good noise. Before the engine has fired up it sounds like a ring and pinion exploded and still being driven. I hope to find the flex plate damaged in the morning as bad as that sounds!! I want my truck back!!
  11. C

    I need some advice

    I hate it but i agree. Enough that i just got home from ordering one.The noise does seem like its coming from there. Using a stethoscope it seems the noise is loudest there too. I dont have a way to do a cutout test. Now when it starts and when the truck is shut off it makes a pretty loud metal...
  12. C

    I need some advice

    Just fine while being driven. It only makes this noise at idle.
  13. C

    I need some advice

    Changed fuel filter and added injector cleaner. No change but i did notice when the speedometer drops back toward 0 is when the noise starts. When it rises the noise stops. This is all done in park at idle.
  14. C

    I need some advice

    If i even touch the throttle the noise is gone. I can hold it at any rpm without a noise at all. I can hold it at 900-950rpm and no noise. Only at idle. youtu.be/k9J4cTqlQGs
  15. C

    I need some advice

    And another. When i touch the throttle at all the noise is gone. Even 100 rpm over idle and its gone. Is it a dirty injector? http://youtu.be/k9J4cTqlQGs
  16. C

    I need some advice

    Here is a link to a video. http://youtu.be/lp_RiMiEiFg
  17. C

    I need some advice

    I just noticed something strange. While sitting still in park idling the speedometer is bouncing around. Kinda steady at 3mph but up and down a little.
  18. C

    I need some advice

    I hooked up my ppe standard and found what says balance rates. I read that the option wasnt therw but thats what it said. The readings were in mm. On startup in park the following were read; 1. 0.6 2. 0.5 3. 1.0 4. 0.3 5. 1.7 6. 0.0 7. 0.0 8. 0.6 After running a few minutes this is what it...
  19. C

    I need some advice

    I put the new boots on it and a water seperator since i broke a wire off of it the other day. I did the pcv re route since i was that deep and need the room to see while its running. It was dark when i finished so i started it hoping the noise was gone, no such luck. I will video it in the...
  20. C

    I need some advice

    I also have the hot side completly off and aside from the lower boot it looks good. I am replacing al boots when they get here.
Top Bottom