Search results

Search the forum Search Articles
  1. MAXX IT OUT

    Info: Any solution for Edge EGT probe

    Is there another way of using a edge CTS to monitor EGT's without there setup? The probe started to fail in short order, so I reached out to EDGE and they said they will send me a new probe. Is there a way to use higher temp and quality sensors. I don't want to go back to individual gauge unless...
  2. MAXX IT OUT

    RCSB Build

    NA 5.3 with mods would make 450HPish at the crank, 14psi of boost with the parasitic loss of the supercharger should around 300-350HP gain, then 20% powertrain loss should put you around 575-625 Wheel HP.
  3. MAXX IT OUT

    Axle seals leaking

    Hum, I think I need to check mine. I just did mine and I believe I did what someone claiming to be a GM teck said was to, which was to torqued it to 52FT LB, then backed it lose and give 1/4 to 1/2 a turn of preload. Might explain why my rotors are dragging on the dust shields when I turn...
  4. MAXX IT OUT

    Winter builds

    That looks so good, I would love to gut a bunch of stuff to make it that clean, but not sure I would give up heat and AC.
  5. MAXX IT OUT

    Winter builds

    More Photos
  6. MAXX IT OUT

    Winter builds

    Anyone have any builds happen over the past winter? Mine ended in Hibernating again this winter with a bunch of little issues, like no glow plugs, hazy injectors, coolant leak from the engine/trans adapters at the block off plate on the passenger side, as well as the coolant return on the oil...
  7. MAXX IT OUT

    "OFFICIAL" What did you do to your D-Max today?

    Finally after a bunch of restarts to get everything thing how I wanted, I got my twins more or less wrapped up, tomorrow I need to make the down pipe, pull everything apart for paint/polish and puts some new injectors in. Hopefully sometime over the next 2 weeks I can make it out to Mark's for a...
  8. MAXX IT OUT

    Oil cooling

    This is where I ended up putting my sensor, I used the glowshift m12-1.5 to 1/8 NTP adaptor and put a oring and thread sealer on it.
  9. MAXX IT OUT

    Info: Powerstop, EBC, or stock brakes?

    I agree with Brad on not using drilled rotors if you do any sort of towing or heavy braking. That's why I ended up going with the Raybesto/ACDELCO wave slotted rotors, but for the price I am willing to give powerstops pads a go.
  10. MAXX IT OUT

    Oil cooling

    So what port do I use for the oil temp sensor? Is it the one on the top like the old oil cooler?
  11. MAXX IT OUT

    Factory style replacement exhaust manifold

    Well I found out that I cracked my passenger side stock ported exhaust manifold and was looking for other options, other than repeating the same issue with another factory manifold or buying a full profab up pipe and manifolds set since I already have Ricks tow flow up pipes. Only two options I...
  12. MAXX IT OUT

    "OFFICIAL" What did you do to your D-Max today?

    Been working on getting this turbo mounted and fine tune its location.
  13. MAXX IT OUT

    G80 locker spring mod

    Well, last night I went to put 2 turns on the spring, but only got 1 turn out of it before it was too short to rest on the other rod.....
  14. MAXX IT OUT

    2wd LLY build

    Were you on that DSM river I80 bridge job?
  15. MAXX IT OUT

    G80 locker spring mod

    How many turns? 2 or 3, or as many as you can?
View older results
Top Bottom