Search results

Search the forum Search Articles
  1. rfletes79

    Another LBY swap

    Well pulled the trigger on a 6 speed conversion for my 02. Should have done this a decade ago. Works extremely well, very happy with it. It’s a DT kit, other then the delay in ordering and shipping it’s been good. Need to get a retune for the 4-5 and 5-6 shift but not a huge issue. I have it...
  2. rfletes79

    59 Apache Duramax

    It’s a factory 59 frame. Ic is an eBay special. We haven’t made the thermostat housing yet but yes it will be facing forward like the Chevelle. I may end up purchasing an HSP as theirs is already made. We’ll see, since we missed hot August nights the build slowed way down. I’ll try and get it...
  3. rfletes79

    Motor Swap-No Start

    What did you swap the short block with??
  4. rfletes79

    LB7 Injector SALE!!!!

    Awesome deal...…..
  5. rfletes79

    LB7 Injector SALE!!!!

    Awesome deal...…..
  6. rfletes79

    59 Apache Duramax

    I just looked up charred wood, hone depot has one in deep navy blue. It looks really good. I think I’m returning what I got and ordering the charred!!
  7. rfletes79

    59 Apache Duramax

    My last progress pic has a plank of the flooring laying in the bed, I’m planning on using it. It’s laminate wood flooring. It’s the weatherproof type, hoping it holds up. Wasn’t that expensive so if it doesn’t work out I won’t be out that much time and money. It looks really good.
  8. rfletes79

    59 Apache Duramax

    Yes
  9. rfletes79

    59 Apache Duramax

    It’s is definitely pointless but in this frame it doesn’t make a difference. As the motor cannot get any lower without being exposed below the crossmember. And when it’s laid out the crossmember is on the ground. We could have removed both pans and modified them like the others but over all...
  10. rfletes79

    59 Apache Duramax

    Progress pics. Motor and trans mount done. Fuel done, radiator installed with ic attached. Trans cooler and lines done. Battery and bed mounted. Windshield in, still waiting on rear window install. Ecm tcm mounted and wired with a donor kodiac harness. Everything is super tight but fits very...
  11. rfletes79

    LB7 fuel line clean up in the valley ??

    This is what I did this last time around with my fuel lines. Zoom in and following the return lines, they’re all there, hooked up and plumbed back to the rear side of the passenger vc. And the feed line feeds directly to the cp3. Sent from my iPhone using Tapatalk
  12. rfletes79

    59 Apache Duramax

    Sent from my iPhone using Tapatalk
  13. rfletes79

    59 Apache Duramax

    Picked her up from the body shop today...... still needs a few finishing touches but this is the look we were going for. Sent from my iPhone using Tapatalk
  14. rfletes79

    59 Apache Duramax

    It’s not done yet!! Going to have a surprise ending.... I hope it looks good.... I have a sneak peak at the fenders already but waiting to see the end result, hopefully soon.
  15. rfletes79

    59 Apache Duramax

    A year later we start on this project...... dropped her off at the body shop a couple weeks ago. Should be picking it up this weekend. Then we start fitting/mocking it all up. Sent from my iPhone using Tapatalk
  16. rfletes79

    Chevelle upgrades.

    Found the gremlin.... Sent from my iPhone using Tapatalk
  17. rfletes79

    04 6.0 to lb7 swap problem class 2 data

    Have you tried pulling the radio and info fuse?? Then try reading/flashing....
  18. rfletes79

    Chevelle upgrades.

    Guess I never posted any updates since getting the new vc on. Car has been running pretty good for the past few months. Ran it in Redding in April, Fontana with NHRA In Super Street (10.90 index) divisional race in may, Sonoma on Memorial Day and this week again at Sonoma. Car has been running...
  19. rfletes79

    Reprogramming a new GPCM with Autocal?

    The data is stored in both modules and need to match. You can read either one then prog the new module with the info you just read.
  20. rfletes79

    LB7: LLY Short Block Into 2001 Wiring

    Cam & Crank Sensors, EOP sensor and associated harness. You will need this items from the 01 short block. You can leave the lly eop sensor in the block as the 01 eop sensor goes in a different location. It will just be plugging the hole with no harness plugged into it.
Top Bottom