Search results
-
T87 Swaps
The issue is, the output level of the Maxx chip is already below what the TCM will accept. We need to go up in voltage from 4v to something between 6-8v. Sent from my SM-S901U using Tapatalk- kidturbo
- Post #393
- Forum: Mike L's Trans Talk
-
T87 Swaps
The goal here is trying to emulate the 2016+ factory sensor, using this small pcb which converts VR sine wave sensor inputs to 5v hall effect outputs. While the output voltage is within range, this circuitry gets knocked down soon as ya connect it to the signal input lines on TCM. Since we need...- kidturbo
- Post #391
- Forum: Mike L's Trans Talk
-
T87 Swaps
Spent a few hours last week playing with these new style speed sensors, after @Cougar281 tested one of the VR converter with his T87 in the truck. While the T87 will accept a powered Arduino Uno pulse signal, it's pull down resistor on the sensor line doesn't work with these 5v VR converters. We...- kidturbo
- Post #389
- Forum: Mike L's Trans Talk
-
LLY Ficm
I was reading where they are very heat sensitive and typically don't survive removal. So I dropped off bag of spares at my FixIt buddy and said just replace all of em.. Think I have a stable bench harness wired up finally. Took a few tries, but I have all the injector signals, along witjh... -
LLY Ficm
As expected, there have been a few bugs to work out. But we have the GPIO's assigned, and the majority are working as designed. First test with the disco light working. [emoji92]️ Basic 200 - 4000 Rpm sweeping. Source: https://youtu.be/svU--39cCxo?si=A1XAb9UkbDlR8C_T Sent from my SM-S901U... -
T87 Swaps
Yeah I can probably make the trip up that way on Monday. Sent from my SM-S901U using Tapatalk- kidturbo
- Post #388
- Forum: Mike L's Trans Talk
-
February '24 Chat -- Leap Year!
Again?? Glad I didn't watch it then..[emoji846] Sent from my SM-S901U using Tapatalk- kidturbo
- Post #49
- Forum: Smoke Signals
-
February '24 Chat -- Leap Year!
I had that exact same thought..- kidturbo
- Post #21
- Forum: Smoke Signals
-
T87 Swaps
Congrats on being first to control an Allison 1000 with a T87 TCM. Now to make it a happy marriage.. :D- kidturbo
- Post #386
- Forum: Mike L's Trans Talk
-
February '24 Chat -- Leap Year!
They were all high a kite on that run, wasn't really a fair fight.. But they did get to keep the trophies, I guess.. [emoji471] https://www.sportscasting.com/michael-irvins-white-house-full-of-sex-drugs-and-plenty-of-cowboys-players/ Sent from my SM-S901U using Tapatalk- kidturbo
- Post #8
- Forum: Smoke Signals
-
February '24 Chat -- Leap Year!
I'm still waiting on my Cowboys to make the big show again. They also had a good streak once, was called the 70's.. :sleep:- kidturbo
- Post #6
- Forum: Smoke Signals
-
Fuel injector knock
A little dielectric grease on the connectors goes a long ways sometimes. I always say start with the electrical side, as a simple latch not snapped in all the ways has got me before. So simple to just disconnect each one and put a bit of grease on em, and reconnect. The slightest voltage related... -
T87 Swaps
Yeah those are the correct part for OEM mat seal option. The latching is a bit more complex to "print" than some others. And while I found the correct wire separator off the female side, haven't been able to locate the mat seal with correct pitch, without buying the whole female connector...- kidturbo
- Post #384
- Forum: Mike L's Trans Talk
-
T87 Swaps
Update on the A50 connector. Found a small issue with the pin choice my 3d modeling expert overbooked, until he got the terminal sockets part printed.. Wrong pitch pins, no fit the spacing.. Had to dig up a different terminal # and he's back on track again. Sometimes, it's the smallest things...- kidturbo
- Post #382
- Forum: Mike L's Trans Talk
-
T87 Swaps
Ok thanks.. It was the Yazaki #7116-4152-02 had me wondering.- kidturbo
- Post #380
- Forum: Mike L's Trans Talk
-
T87 Swaps
What ya find for terminal cross reference numbers? I'm just placing an order for a few connectors.- kidturbo
- Post #378
- Forum: Mike L's Trans Talk