Search results

Search the forum Search Articles
  1. D

    Cab mounts

    nevermind, i'm an idiot.
  2. D

    Cab mounts

    I have a quick question, I bought the new hydraulic mounts, lower cushion and retainer but for the life of me i cant get the new upper mounts to fit through the hole. it was fairly rusty, but i filed the shit out of it and even filed the edges of the mount but it wont go. Almost seems like its...
  3. D

    Hard Shifts from 1-2, 3-4 and P to D

    Thanks man, put about 100km so far and way better already. U da man mike!
  4. D

    Hard Shifts from 1-2, 3-4 and P to D

    Update: So I pulled the valve body out last night and checked out the trim valves and springs. And what do you know? The small spring above the check ball in the B-trim valve was collapsed pretty good. I have a pic, but can't upload it right now. I put everything back together with a new transgo...
  5. D

    Hard Shifts from 1-2, 3-4 and P to D

    Thanks a lot Mike, I'll try and make some time to have a look at it. Really appreciate the input. If I find anything, I'll keep u posted (might be a little while).
  6. D

    Hard Shifts from 1-2, 3-4 and P to D

    This is probably a dumb question, but if it was a broken spring on a trim valve or stuck valve could this be repaired without removing the tranny? I ask because I know if you put on a transgo shift kit (which it has), the tranny has to come out... Thanks
  7. D

    Hard Shifts from 1-2, 3-4 and P to D

    No codes, had it at the mechanic on Tuesday, reset the taps but didn't really help. 3-4 shift is getting worse and slams into gear now. Talked to the builder, who is a 2 hr drive away, and he said I should do I line pressure test??? And probably a stuck valve or solenoid problem? Is the spring...
  8. D

    Hard Shifts from 1-2, 3-4 and P to D

    So this is a recent problem (2 days ago), i haven't modified my truck in like 6 months so its not a tuning issue as far as i know. All of a sudden it's been shifting pretty hard from 1st to 2nd at partial throttle, it's almost like it revs up a bit, then hammers in gear. 3-4th is similar but not...
  9. D

    LLY: How much can a stock bottom end LLY take?

    I think anything over 600hp on stock injectors and CP3 is impressive! I don't think my truck would do it.
  10. D

    LLY: How much can a stock bottom end LLY take?

    I run the II s366 on my stock bottom end and stock studs with no problems @ just over 500HP and 900Ft/Lbs). I'm throwing a set of 45 overs in this spring which may make things a little more interesting. If you have a stock (original) CP3 it's unlikely you would have enough fuel to break the...
  11. D

    Reputable Calgary Shops

    Broken Axle in Aveneda Mall just off macloed trail has a pretty good reputation.
  12. D

    Nova vs. ccsb lb7

    All the stuff above, plus 40 overs, Upgraded turbo (4094, S366, etc), and water meth and I'd think it would be real close!
  13. D

    Question: Rear Wheel Spacers... Who is running them?!? Yes or No?!?

    I run Freds 2" in rear and they are rock solid. You get what you pay for, I wouldn't want to cheap out then loose a tire going 80mph while towing!
  14. D

    Silver Bullet S366

    Ok guys, update. So I did unhook the feed line and started it for like 2 seconds and the feed line started firing oil out.. so good there (didn't read the previous post until now). I then found that my drain tube was leaking a bit right from the turbo. What a pain in the ass trying to tighten...
  15. D

    Silver Bullet S366

    Maybe ill try the bucket thing, just for peace of mind. thanks
  16. D

    Silver Bullet S366

    Thanks for the replies guys, turbo is in and she rips! Sounds amazing too. Ground down the mouthpeice and it fits great, and for the exhaust i just matched it up, and clamped her down tight as @%#~. Got a couple questions though. So been driving the truck around and it runs great but i keep...
  17. D

    Silver Bullet S366

    Ok, so just grind off the excess around the afe piece to make it fit, Sounds simple enough. Just didn't want to start ruining good pieces if I didnt need to. I wish the directions were a little clearer..lol. As for the exhaust, i'll just make it work somehow and probably take it to an exhaust...
  18. D

    Silver Bullet S366

    Hey guys, I don't post very often but I definitely find this site very useful, and have a little dilemma. So i'm in the process of installing the II S366 Silver bullet right now (kind of on hold b/c BD diesel sent me the wrong install kit) and just have a few questions for anyone that has any...
Top Bottom