Search results

Search the forum Search Articles
  1. L

    LBZ: Engine/Fuel Limp Mode

    stock transmission, yes. I was in my "trans safe" tune. +80-100hp? Not completely sure.
  2. L

    LBZ: Engine/Fuel Limp Mode

    I wasn't pulling anything but I was accelerating hard both times
  3. L

    LBZ: Engine/Fuel Limp Mode

    I used my Edge Insight CTS 2
  4. L

    LBZ: Engine/Fuel Limp Mode

    I checked for codes both times, none were given
  5. L

    LBZ: Engine/Fuel Limp Mode

    I have a 2006 2500 CCSB, 310K miles, EFI Live w/ CTSII, AirDog 4G, EGR delete. The ground on my lift pump got pulled off a month ago or so and I limped my truck for the 1st time since I bought it after a hard pull. I still had all 6 gears but was limited to 2k RPM. After some research I found...
  6. L

    LBZ: MAP Sensor code?

    Yes, I haven't had the codes thrown since April. I used some electrical cleaner initially on the sensors and it helped but it was only a temporary fix for me. I ended up replacing the MAP and MAF sensors, both. I think my truck had to get used to the parameters on the new sensors so the codes...
  7. L

    LBZ: MAP sensor throwing check engine light, things to check for?

    http://www.duramaxdiesels.com/forum/showthread.php?t=70976 See if this helps. I ended up replacing the MAF and MAP sensors, used some electrical cleaner and the issue resolved itself. As I was told, it helps to have the code(s) that is/are being thrown
  8. L

    LBZ: Blower motor and resistor

    Hey everyone, I think I need a new blower motor but I want some 2nd and 3rd, and however many more opinions from people that probably know a lot more about this than I do. I noticed before that my A/C would randomly start blowing harder/softer but didn't think much of it. Got to the beach last...
  9. L

    LBZ: MAP Sensor code?

    I took a look at everything and all the wires look fine. No cuts, no dry-rot, nothing loose. After talking to a friend, I bought some electrical cleaner yesterday and cleaned all of the harness' and that has made a huge difference. None of the codes have been thrown again yet so I'm hoping that...
  10. L

    LBZ: MAP Sensor code?

    You mentioned boost. I just saw P0299 tonight for the 2nd time, along with P0106, since this whole issue started but I still didn't see any issues with performance other than going into limp mode which is easily fixed by clearing the codes. I'm going to take a look at the wiring tomorrow at work...
  11. L

    LBZ: MAP Sensor code?

    MAF sensor was thrown this morning when I left work. It was P0101. I'm gonna try and take a close look at the wiring for my map sensor
  12. L

    LBZ: MAP Sensor code?

    So I just went and checked my iQ history and it jogged my memory a little. There was a code 13 and code 14 on my tuner diagnostics and then on my vehicle diagnostics was P0106, P0237(only saw once after my truck sat a few days), and I think the MAF sensor was P0101 but I'm not 100% sure.
  13. L

    LBZ: MAP Sensor code?

    Sorry, P0106 is the one that keeps getting thrown. I cant remember the other 2 off the top of my head. I'll see if I can find where I wrote them down at
  14. L

    LBZ: MAP Sensor code?

    Hey, I have a 2006 LBZ 2500(Banks six-gun with speedloader and iQ, 5" straight pipe). It started throwing a MAP sensor code about a month ago. I replaced the MAP sensor which ended up only being a bandaid. It still throws the same code and will occasionally throw a MAF sensor code as well. A...
Top Bottom