Search results

Search the forum Search Articles
  1. 0

    Fuel in oil

    I think it'll work for a $1000 truck! Lol now to figure out these dang steering wheel buttons!
  2. 0

    Fuel in oil

    I figured out the problem. Someone had #3 and # 5 injector wires crossed. I was just messing around and seen that the one plugged into 3 ran all the way back in the harness with #7 so I swapped them and it's running like new with balance rates in spec! #5 had been cut and spliced before
  3. 0

    Fuel in oil

    No one has any tips or ideas on how to find a wiring/ electrical issue?
  4. 0

    Fuel in oil

    I checked the voltage on #3 injector I was getting 6.1 on wire and 6.3 on the other. I checked #2 injector that is showing good balance rates and I read 5.9 on both wires. I also cleaned the MAF as I read this could cause problems but no luck.
  5. 0

    Fuel in oil

    It has oil pressure I think it was problem with the stepper motor. I only paid a $1000 for the truck I think I'm way ahead
  6. 0

    Fuel in oil

    I have done the ice pick trick. I will check with a volt meter. I can't remember if I said before but once warmed up it smokes really bad like a stuck injector. Ughh this truck is a headache!!
  7. 0

    Fuel in oil

    Ok I just changed #3 injector with #7 and the problem stayed with #3. I'm know thinking it is the wiring. How can I check this?!
  8. 0

    Fuel in oil

    Ok I was thinking about doing this but didn't know if I would need new o rings or anything because I don't have any.
  9. 0

    Fuel in oil

    Since I'm using dash command on my phone, has there been any problems with cylinder not matching with what the app is telling you? I'm assuming it's right since I was getting a code for misfire in 3 and 5. Also as the truck was idling I messed around with unplugging injectors I can unplug 3,5...
  10. 0

    Fuel in oil

    Who ever had the truck obviously knew about this because there was a ton of tape a wire loom around the harness by the Alternator bracket. I checked the wires there and everything looked good. Is there a way to use a bolt meter to check wiring at injector while it's running? What would I be...
  11. 0

    Fuel in oil

    I ran compression test on 1,3,5,7 and they were all around 350. So it's looking like it may be injectors but would this be the reaso I was getting fuel in my oil??
  12. 0

    Fuel in oil

    P0300. P0700 P0303. C0040 P0305. C0035 P0401. C0055 P0404. B0024 P0463. B0026 U1016. What should compression be on these motors?
  13. 0

    Fuel in oil

    I finally got my obd2 wifi reader today. I pulled the 13 mil codes two of which were p0303 and p0305 cylinder 3/5 misfire. I am also reading a balance rate of 15mm on these two injectors. What does this mean?? Injector is clogged or flowing to easy??
  14. 0

    Fuel in oil

    I can find them all day long for the cummins cp3. I'm just wondering if they are the same?
  15. 0

    Fuel in oil

    Is there anyway to just replace the seal on the cp3? I seen where a company called wicked diesel used to sell these but I can't find them.
  16. 0

    Fuel in oil

    It is a 2005 lly with 224,000 miles. I just changed the oil since I noticed the oil change sticker was 10,000 miles over due. It built up oil pressure for a little but then it fell off. I pulled the truck up to the house and noticed it felt very weak.
  17. 0

    Fuel in oil

    I just picked up a 2005 3500. The guy I bought it from said the rear main seal was leaking. After getting the truck home I drained the oil to find that it had about 4 gallons in it and it smelled like diesel. Does anyone know what it may be? Injectors? Cp3? Any way to check each item?
Top Bottom